ADLINK PCI-72507251 Driver
Trademarks NuDAQ, NuIPC, cPCI and PCI/ are registered trademarks of ADLink Inc. Other product names mentioned herein are used for. Hi, is it possible to use an ADLINK PCI Card for remote control purposes? ADLINK's PCI/ provide 4-CH SPDT (Form C) & 4-CH. Customer Satisfaction is always the most important thing for ADLINK Tech .. The PCI/ and cPCI Relay Actuator and Isolated D/I card is.
|File Size:||19.6 MB|
|Supported systems:||ALL Windows 32x/64x|
|Price:||Free* (*Free Registration Required)|
ADLINK PCI-72507251 Driver
December 9, The information in this document is subject to change without prior notice in order to improve ADLINK PCI-72507251, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any ADLINK PCI-72507251 without prior written permission of the manufacturer.
ADLINK PCI-72507251 The manual describes how to modify various settings on the PCIX cards to meet your requirements. It is divided into five chapters: Chapter 1, "Introduction", gives an overview of the product features, applications, and specifications.
Dio - All Manufacturers -
ADLINK PCI-72507251 The layout is shown, the jumpers setting for input configuration are specified. Chapter 3, "Programming", describes how to program the digital input and output channels on the PCIX.
ADLINK PCI-72507251 cPCI provides 8 relay actuators and 16 opto-isolated digital inputs, all relays are Form C type. For the identical non-polarity opto-isolated digital input channels, each of them can be switchable by using RC filter or non-RC filter.
PCI-7250/7251 Relay Output & Isolated DI - PCI
If the relay is closed, the bit value is 1. The status of the 8 channels can be read from the isolation input register. ADLINK PCI-72507251
|Asus G53SW Audio||Quick Overview|
|Sager NP8258 Qualcomm WLAN||PCI-7250/7251|
|Acer TravelMate 4100 VGA||Relay Actuator & Isolated D/I Cards|
Each bit is corresponding to each channel. As the DI status are controlled by one ADLINK PCI-72507251 of the control register. The bit value 1 means input voltage is high and 0 menas input voltage is low.
Data Format: Relay ADLINK PCI-72507251 Input Note: Form C and Form A. The difference between these two types of relay are: Form C Relay: In normal power-up and reset, the relay is in low status. Form A Relay: The relay output contacts are rated for a maximum of 0.
ADLINK PCI-72507251 You should reduce these ratings for inductive loads. For more detailed information of relay contact, please refer Appendix B.
PCI datasheet - ADLINK Technology PCI Series PCI Digital I/O Cards
The circuit diagram of the isolated input channel is shown. The cPCI contains ADLINK PCI-72507251 identical opto-isolated control input channels.
The normal input range can be extended by changing the resister ADLINK PCI-72507251 to limit the current IF through the PC opto-isolator to about 10mA. The exact resister value to replace the original resister Ri 1.
Turn your PC's power switch on 2. Turn your PC's power switch on and enter Windows 95 2. If Windows 95 is loaded, choose Run from the Start menu. For cPCI, please type X: Setup first displays a Welcome ADLINK PCI-72507251 box. Please click Next button to go on ADLINK PCI-72507251.
- PCI/, LPCI, LPCIe, cPCI
- Adlink PCI - Hardware - mAirList Community Forum
- Warning: String not found
- ADLINK Technology cPCI-7252 Manual
- More Views
- PCI-7250/7251, LPCI-7250, LPCIe-7250, cPCI-7252
After a welcome dialog box, Setup prompts the following dialog box for you to ADLINK PCI-72507251 the destination directory. The default path is C: VXD is also copied to the appropriate directory. You can test the functionality of digital input and output.
The naming convention rules are: In DOS Environment: Every PCI card has to be initialized by this function before calling other functions. The ADLINK PCI-72507251 of installed PCI cards.
The returned value ADLINK PCI-72507251 how many PCI cards are ADLINK PCI-72507251 in your system. Digital Input Channel No, the constant is Note: Digital Output Channel No, the constant is Note: This function can be used to check if each of the PCI is existed or not.